Upgrade Kits for Magnetek/Parallax
  Progressive Dynamics Converters
  Boondocker Converters
  Replacement Lower Converter Assembly for WFCO 8955
  WFCO Converters
  Airstream Converters and More
  Voltminder
  Iota DLS Converters
  Parallax Magnetek Converters
  Centurion CS 3000 Replacement
  Elixir Replacement Converter
  American/Centurion CS 6000 Converter
  Pop Up and Small Camper Converters
  Battery Monitors
  Lithium (LiFePO4) Deep Cycle Batteries
  AGM Deep Cycle Batteries
  SmartPlug Inlets and Cordsets
  Zamp Solar
  RV Surge Protectors
  RV Power Protection EMS
  Parallax Paramode with TempAssure
  Lithium Battery Converter Chargers
  Cotek Inverters & Chargers
  Samlex EVO Inverter Chargers
  Samlex Pure Sine Wave Inverters
  Xantrex TrueCharge2 Chargers
  Xantrex Pure Sine Wave Inverters
  Xantrex Freedom 458 Inverter/Chargers
  Specialty Converters
  WFCO Pure Sine Wave Inverters
  Inverter Class T Fuses
  Distribution Panels
  DC Fuse Panels
  Transfer Switches
  SeeLevel Gauges
  Dinosaur Electronics
  Circuit Breakers and Fuses
  Solar Charger Maintainers
  Adapters Plugs Receptacles
  Shunts
  Battery Disconnects
  Battery Minder Battery Chargers
  Automatic Load Shed
  12 Volt LED Interior Lighting
  Pressure Pro
  24 Volt Converters
  48 Volt Converters
  240 VAC Converters (European)
  Marine Battery Chargers
  Spendide Washer/Dryer Repair
  Victron Energy
  Progressive Dynamics Pure Sine Inverters
LL-12V100-24 LL-12V100-24
EV-BM350 Expion360 BM350 Battery Monitor
C30303BM30PG 30 Foot Cordset with Grey Inlet C30303BM30PG
B50ASSYPG 50 Amp Female Connector and Gray Inlet B50ASSYPG
SP-3000-124 3000 Watt 24 Volt Pure Sine Inverter SP-3000
0 item(s) in your cart / Total: $0 View Cart Checkout
Home > SeeLevel Gauges
 

SeeLevel Gauges

 
 
 
 Products (Total Items: 2)
Extra Sender Board
Extra Sender Board
Your Price: $56.00
Junior Sender Board
Junior Sender Board
Your Price: $56.00
 
 
 
 
Provides accurate tank level information using percentage of full readout
 
Tanks are monitored using Garnet’s proprietary external level sensing technology. This ends fouling problems caused by debris build-up in the holding tank.
 
Detailed diagnostic information monitors sender operation.
 
Measures tanks up to 12 inches tall with a single sender or 24 inches tall with dual senders

Tank senders connect to display via a one wire bus which saves wiring costs

LPG tank connection compatible with existing electric senders

Calibrate LPG at first fill of tank or it can be factory calibrated

Multiple versions meet the needs of differing configurations:

709PH: Three holding tanks, LPG tank,water pump/heater switches

709: Three holding tanks, LPG tank

709-4: Four holding tanks

Uses common industry connector for ease of installation and servicing
 
Resolution: 3/8 inch (10 mm)

Accuracy: +/- 10% or better, limited by resolution and tank shape

Operating temperature range: +32 to +140 oF (0 to + 60oC)

Sender materials: 0.008” thick glass epoxy circuit board with conformal coating for circuit protection. Laminated on the back with 3M 300LSE Bonding Adhesive.

Display mounting panel: Black panel, approximately 4” wide by 2.8” high by 1” deep (102mm wide X 71mm high X 25mm deep). Panel screws to wall. Required cutout size is 3” wide by 1.8” high.

System power requirements: Display requires 12 volts from the RV battery, the system will function from 11 volts to 16 volts. Current drain is less than 200mA.

Wiring: Common two wire conductor (signal and ground) required from the display to each sender. 12 V power and ground required for display. Single wire required for LPG sender if sender grounded at tank.

LPG sender characteristics: Display will work with an LPG sender maximum resistance of 50 ohms to 500 ohms. Display shows increasing level as resistance increases. System must be calibrated with the LP tank full, or can be factory calibrated.