Upgrade Kits for Magnetek/Parallax
Progressive Dynamics Converters
Boondocker Converters
Replacement Lower Converter Assembly for WFCO 8955
WFCO Converters
Airstream Converters and More
Voltminder
Iota DLS Converters
Parallax Magnetek Converters
Centurion CS 3000 Replacement
Elixir Replacement Converter
American/Centurion CS 6000 Converter
Pop Up and Small Camper Converters
Battery Monitors
Lithium (LiFePO4) Deep Cycle Batteries
AGM Deep Cycle Batteries
SmartPlug Inlets and Cordsets
Zamp Solar
RV Surge Protectors
RV Power Protection EMS
Parallax Paramode with TempAssure
Lithium Battery Converter Chargers
Cotek Inverters & Chargers
Samlex EVO Inverter Chargers
Samlex Pure Sine Wave Inverters
Xantrex TrueCharge2 Chargers
Xantrex Pure Sine Wave Inverters
Xantrex Freedom 458 Inverter/Chargers
Specialty Converters
WFCO Pure Sine Wave Inverters
Inverter Class T Fuses
Distribution Panels
DC Fuse Panels
Transfer Switches
SeeLevel Gauges
Dinosaur Electronics
Circuit Breakers and Fuses
Solar Charger Maintainers
Adapters Plugs Receptacles
Shunts
Battery Disconnects
Battery Minder Battery Chargers
Automatic Load Shed
12 Volt LED Interior Lighting
Pressure Pro
24 Volt Converters
48 Volt Converters
240 VAC Converters (European)
Marine Battery Chargers
Spendide Washer/Dryer Repair
Victron Energy
Progressive Dynamics Pure Sine Inverters
Schumacher Converter Upgrade
Parallax 555/5355 to Boondocker Upgrade
Magnetek Upgrade
Testimonials
Terms & Conditions
EV-BM350 Expion360 BM350 Battery Monitor
R50304BM50S R50304BM50S | 50 AMP 30’ DUAL CONFIGURATION SMARTPLUG CORDSET W/STAINLESS STEEL INLET
C30303BM30PG 30 Foot Cordset with Grey Inlet C30303BM30PG
R30303BM30NT 30 Foot Cordset with Stainless Inlet R30303BM30NT
B50ASSYPG 50 Amp Female Connector and Gray Inlet B50ASSYPG
Subscribe to our Newsletter.
Enter your Email address below and press the GO button.
0 item(s) in your cart / Total: $0
View Cart
Checkout
Home
>
Zamp Solar
>
Zamp C-PAP Power System
Zamp C-PAP Power System
Zamp ZP-600PS-CPAP Power System
Power 2 CPAP Machines Using your On-board Battery System
C-PAP Power System Main Control Panel
Our CPAP power system is equipped with a main control panel that can be mounted up to 25' away from the inverter. This main control panel also acts as a remote switch for inverter operation. The main control panel houses the AC ports, voltage readouts and the main switches for turning on and off the LED voltage readout and remotely turning on and off the inverter. In addition to the voltage readout is a battery health indicator chart located on the bottom of the main control panel face plate. Use the voltage readout to compare at what health your battery is to ensure you have the power to last the night. This main control panel can be easily surfaced or flushed mounted close to sleeping quarters for function and convenience.
Special 600 Watt CPAP Pure Sine Wave Inverter
Our CPAP pure sine wave inverter is specially designed to give the greatest efficiency and flexibility. This inverter uses AC direct connect ports that can extend the AC outlets over long distances. Keeping the inverter close to the battereis helps increase the efficiency of the inverter while allowing the power supplied from the inverter to be used at greater distances. Our CPAP pure sine wave inverter also incorporates a remote switch options for turning the inverter on and off.
Complete Kit with Pre-Wired and Pre-Cut High Quality Wire
We’ve done much of the wiring need and made it very easy to install our CPAP power system. Color coded wires and many of the wire ends have been pre-wired for their specific locations. There are only a few wires with cut ends that that need to be wired with wiring connections to. This allows greater installation flexibility. Our wire is a copper strand core and the wire size and length have been properly configured for this set up.